HomeStage 3 · In the fieldFive basic knots guide
By Global PrepperUpdated 1 official sourceHow we make the guides
Stage 3 · Five basic knots guideFive knots: one rope, a thousand uses
With a rope and five knots you can lash a shelter, hang your load and adjust a tarp. Each knot does a different job: learn which to use and practice them before you need them.
- Each knot has its job: loop, hitch, adjustment or join.
- Tighten and pull to test the knot: a loose one slips or comes undone.
- Leave a tail of rope after the knot so it does not come loose.
- Practice them with the rope in your hand, not just by reading.
A loop that does not slip: bowline and figure eight
Two terms: the standing part is the rope you do not use to tie the knot; the working end is the tip you tie it with.
- Make the holeForm a small loop in the standing part, with the working end on top. The farther it is from the tip, the bigger the loop will be.
- The rabbit comes outPass the working end up through the hole, from below: it is the rabbit coming out of its burrow.
- Go around the treeTake it behind the standing part, which acts as the tree.
- Go back in and tightenPut it back into the hole, from above, and pull the standing part and the working end at the same time.
- Figure eight: make a loop, pass the tip behind the standing part and push it through the loop. Tighten: it forms an 8. It works as a stopper so the rope does not slip out of a hole, and with the rope doubled it makes a very firm loop.
- Which one to use: the figure eight weakens the rope less, so it is preferred today for rescue; the bowline is easier to untie after it has been loaded.
The video shows the bowline.
Tie down and adjust: clove hitch and taut-line hitch
The clove hitch fastens a rope to a trunk or a post and is used to start and finish lashings. The taut-line hitch slides along the rope to tighten or loosen it, and stays where you leave it: it is the knot for the tarp and guy lines of a shelter.
- Clove hitch: wrap and crossTake the working end once around the trunk or post and cross it over the standing part.
- Clove hitch: second turnMake another turn, tuck the working end under the crossing and tighten.
- Taut-line hitch: the turnsGo around the stake or tree and come back along the standing part. With the working end, make two turns around the standing part, on the stake side, and a third one farther from it.
- Taut-line hitch: tighten and adjustTighten the turns. Slide the knot toward the stake to tension or toward you to loosen.
The clove hitch loosens if the rope goes slack. Keep it taut, or make one more turn around the trunk and under the center of the knot.
The video shows the taut-line hitch.
Join two ropes: square knot
The square knot joins two ropes of the same thickness. It is easy to check and to untie after use.
- Right over leftHold one end in each hand. Cross the right one over the left and pass it underneath, like the first step of tying your shoes.
- Left over rightNow cross the end that is on the left over the one on the right and pass it underneath.
- Tighten and checkPull both ropes. It should lie flat and even; if it comes out twisted or diagonal, undo it and repeat.
- Secure the endsFinish each end with an overhand knot so it does not come loose.
Do not use the square knot if a life depends on the join. It can come loose if the ropes are of different thickness or if you do not secure it.
- Practice all five until they come out without thinking.
- Keep a practice rope in your backpack and repeat them once a month.
Check what you already have
0 of 5 · Saved only on this device.
- Leaving knots loose: they slip or come undone.
- Leaving the clove hitch without tension: it loosens on its own.
- Using a square knot to join ropes of different thickness or to hold something that matters.
Sources: US Army Survival Manual · appendix G, ropes and knots